Рассчитать расход ткани на оконные шторы
Длина занавески
Для того, чтобы определить расход ткани на шторы необходимо знать следующее:
Ширина занавески Ширину полотна определяют длина карниза и вид желаемого крепления занавески к карнизу. Количество необходимой материи меняется в зависимости от вида крепления. Подсчитать, сколько понадобится ткани, можно с достаточной точностью, зная коэффициент сборки.
Как рассчитать шторы для стандартного окна
Это полезно: Если раппорт очень крупный, используйте оставшиеся после раскроя куски ткани для подхватов или декоративных подушек.
Length of the curtain
In order to determine the consumption of cloth on curtains, you need to know the following:
Length of curtains
Width of the curtains
Three types of curtain length are adopted:
How to calculate the fabric on the curtains to the windowsill
1. To the window sill (A) — the bottom edge of the curtain is 1 cm above the sill, so that it can move freely;
How to calculate the fabric on the curtains below the windowsill
2. Below the windowsill (B) — the curtains look neater if they hang 10-15 cm below the windowsill;
How to calculate the fabric for the blinds to the floor
3. To the floor (C) — the curtains end 1 cm above the floor level, so that they wear less. But in the event that you do not interfere with the fabric, and you are not afraid that it is worn, you can choose the length of the curtains so that the fabric falls to the floor.
This is useful
Calculation of fabric for curtains, if possible, produce not a centimeter, but a steel tape measure. It is longer and allows more accurate measurements.
To determine the length of the curtain, measure the distance from the top of the anchored rail or from the base of the rings on the rod to the intended position of the curtain at the bottom. The allowances for the hem are not taken into account yet, you will add them later when calculating the consumption of fabric.
2Width of the curtain
The width of the web is determined by the length of the cornice and the type of desired attachment of the curtain to the cornice. The amount of necessary matter varies depending on the type of attachment. To calculate how much tissue you need, you can with sufficient accuracy, knowing the coefficient of assembly.
Mounting type and assembly factor:
This is useful
Before you start to measure, strengthen the cornice in the right place so that you can measure the length and height. The cornice is placed above the window at a distance of 7.5-12.5 cm. On the sides of the window the cornice protrudes by 15 cm so that the curtains can be opened and the room lit up.
Loops — a factor of 1.5-2
Curtain hinges
Curtains on curtains
Eyelets — coefficient 2
Standard curtain
Tape — coefficient 2
Curtains with curtain tape
Curtains with pencil folds
Pencil folds — a factor of 2 — 2.5
Triple folds — coefficient 2
Curtains with triple folds
Curtains with puffs
Buffers — a factor of 2.5
This is useful
When calculating the width of the curtains on both sides, add 10 cm to the hem of the sides.
3How to calculate the curtains for a standard window
How to Calculate Cloth for Curtains
The length of the ledge is 2 meters
Height of curtains — 2.6 meters
Build factor — 2
TULLE
Fabric consumption per tulle (height of the fabric) = height of the curtains + hem of the bottom + upper limb = 2.6 m + 0.15 m + 0.10 m = 2.85 m
Fabric consumption per tulle (width of web) = length of the cornice X assembly factor = 2 m X 2 = 4 m
PORTRAITS
Fabric consumption per curtain (according to the height of the fabric) = height of the curtains + hem of the bottom + upper limb = 2.6 m + 0.15 m + 0.10 m = 2.85 m
Fabric consumption per curtain (width of fabric) for one cloth = (length of the curtain X assembly factor): for the number of canvases = (2 mx 2): 2 = 2 m
This is useful
If the rapport is very large, use the remaining pieces of cloth for pickups or decorative pillows after cutting.
ATTENTION!
For a fabric with a printed or geometric pattern that repeats along the length of the fabric (rapport), its consumption increases by the length of the rapport. For example, if the size of the rapport is 60 cm, then you need to buy fabrics for 60-65 cm more than necessary to fit the pattern.
Для того, чтобы определить расход ткани на шторы необходимо знать следующее:
- длину занавесок
- ширину занавесок
| Приняты три типа длины занавески: | |
 1. До подоконника (А) — нижний край занавески находится на 1 см выше подоконника, так что может беспрепятственно двигаться; | |
 2. Ниже подоконника (В) — занавески смотрятся аккуратнее, если свисают на 10-15 см ниже подоконника; | |
 3. До пола (С) — занавески заканчиваются на 1 см выше уровня пола, чтобы они меньше изнашивались. Но в том случае, если вам ткань не мешает, и вы не боитесь, что она износится, то можно выбрать такую длину штор, чтобы ткань ниспадала на пол.Это полезно Расчет ткани для штор по возможности производите не сантиметром, а стальной рулеткой. Она длиннее и позволяет точнее снять мерки. | |
| Для определения длины занавески измерьте расстояние от вершины закрепленного рельса или от основания колец на штанге до предполагаемого положения шторы внизу. Припуски на подгибку пока не учитывайте их вы добавите позднее при расчете расхода ткани. | |
| ||||||||||||
Петли — коэффициент 1,5-2
Люверсы — коэффициент 2
Стандартная гардинная
Карандашные складки — коэффициент 2 — 2,5
Тройные складки — коэффициент 2
Буфы — коэффициент 2,5 Длина карниза — 2 метраВысота штор — 2,6 метра Коэффициент сборки — 2 ТЮЛЬ Расход ткани на тюль (по высоте полотна) = высота шторы + подгиб низа + подгиб верха = 2,6 м + 0,15 м + 0,10 м = 2,85 м Расход ткани на тюль (по ширине полотна) = длина карниза Х коэффициент сборки = 2 м Х 2 = 4 м ПОРТЬЕРА Расход ткани на портьеру (по высоте полотна) = высота шторы + подгиб низа + подгиб верха = 2,6 м + 0,15 м + 0,10 м = 2,85 м Расход ткани на портьеру (по ширине полотна) для одного полотна = (длина карниза Х коэффициент сборки) : на количество полотен = (2 м Х 2) : 2 = 2 м |
| ВНИМАНИЕ! Для ткани с набивным или геометрическим рисунком, который повторяется по длине ткани (раппорт), расход ее увеличивается на длину раппорта. Например, если размер раппорта 60 см, то нужно купить ткани на 60-65 см больше необходимого для подгонки рисунка. |
In order to determine the consumption of cloth on curtains, you need to know the following:
Length of curtains
Width of the curtains
Three types of curtain length are adopted:
How to calculate the fabric on the curtains to the windowsill
1. To the window sill (A) — the bottom edge of the curtain is 1 cm above the sill, so that it can move freely;
How to calculate the fabric on the curtains below the windowsill
2. Below the windowsill (B) — the curtains look neater if they hang 10-15 cm below the windowsill;
How to calculate the fabric for the blinds to the floor
3. To the floor (C) — the curtains end 1 cm above the floor level, so that they wear less. But in the event that you do not interfere with the fabric, and you are not afraid that it is worn, you can choose the length of the curtains so that the fabric falls to the floor.
This is useful
Calculation of fabric for curtains, if possible, produce not a centimeter, but a steel tape measure. It is longer and allows more accurate measurements.
To determine the length of the curtain, measure the distance from the top of the anchored rail or from the base of the rings on the rod to the intended position of the curtain at the bottom. The allowances for the hem are not taken into account yet, you will add them later when calculating the consumption of fabric.
2Width of the curtain
The width of the web is determined by the length of the cornice and the type of desired attachment of the curtain to the cornice. The amount of necessary matter varies depending on the type of attachment. To calculate how much tissue you need, you can with sufficient accuracy, knowing the coefficient of assembly.
Mounting type and assembly factor:
This is useful
Before you start to measure, strengthen the cornice in the right place so that you can measure the length and height. The cornice is placed above the window at a distance of 7.5-12.5 cm. On the sides of the window the cornice protrudes by 15 cm so that the curtains can be opened and the room lit up.
Loops — a factor of 1.5-2
Curtain hinges
Curtains on curtains
Eyelets — coefficient 2
Standard curtain
Tape — coefficient 2
Curtains with curtain tape
Curtains with pencil folds
Pencil folds — a factor of 2 — 2.5
Triple folds — coefficient 2
Curtains with triple folds
Curtains with puffs
Buffers — a factor of 2.5
This is useful
When calculating the width of the curtains on both sides, add 10 cm to the hem of the sides.
3How to calculate the curtains for a standard window
How to Calculate Cloth for Curtains
The length of the ledge is 2 meters
Height of curtains — 2.6 meters
Build factor — 2
TULLE
Fabric consumption per tulle (height of the fabric) = height of the curtains + hem of the bottom + upper limb = 2.6 m + 0.15 m + 0.10 m = 2.85 m
Fabric consumption per tulle (width of web) = length of the cornice X assembly factor = 2 m X 2 = 4 m
PORTRAITS
Fabric consumption per curtain (according to the height of the fabric) = height of the curtains + hem of the bottom + upper limb = 2.6 m + 0.15 m + 0.10 m = 2.85 m
Fabric consumption per curtain (width of fabric) for one cloth = (length of the curtain X assembly factor): for the number of canvases = (2 mx 2): 2 = 2 m
This is useful
If the rapport is very large, use the remaining pieces of cloth for pickups or decorative pillows after cutting.
ATTENTION!
For a fabric with a printed or geometric pattern that repeats along the length of the fabric (rapport), its consumption increases by the length of the rapport. For example, if the size of the rapport is 60 cm, then you need to buy fabrics for 60-65 cm more than necessary to fit the pattern.