Как правильно положить линолеум
Способы укладки
Подсчет необходимого количества материала
Подготовка Пол должен быть плоским, чистым, сухим и очищенным от пыли: если на полу есть неровности или трещины, необходимо заранее выровнять его нивелирующей смесью.
Как положить линолеум без приклеивания
Дополнительные советы Для того чтобы добиться незаметного стыка в случае необходимости состыковки полос:
Ways of styling
Way of packing
Recommended use Advantages Disadvantages
Stacking without gluing Suitable for rooms with an area of no more than 12 m2 or for premises with low attendance
Fast
Stowage
Risk of rapid wear
Significant risk of formation of «waves»
Bonding on double-sided scotch tape
Suitable for rooms with average attendance
Fast
Stowage
Risk of formation of «waves»
Leaves marks after peeling off the coating
Bonding with glue intended for fast gluing and removal of coating. Mandatory for rooms larger than 20 m2 or for rooms with significant attendance
Rapid roll packing
Easy peeling off
Significantly increases the service life of the coating
Adhesive bonding with special professional adhesive. Mandatory for rooms larger than 20 m2 or for premises with significant attendance
High-strength bonding for long-term use
Significantly increases the service life of the coating
Labor-intensive peeling off
2 Counting the required amount of material
Calculating the amount of linoleum for laying 1. Measure the maximum length and width of the room.
2. Add 10 cm to the measurements.
3. Take into account the ledges (the space under the wall cabinets, the window, the door).
4. When combining the pattern, it is necessary to calculate the amount of material in such a way that there remains a margin for one repeat of the pattern in each direction.
3 Preparation
The floor must be flat, clean, dry and free from dust: if there are unevenness or cracks on the floor, it is necessary to level it with a leveling mixture beforehand.
Preparation of linoleum for laying 1. Unfold the roll and spread the coating in the room, leaving a margin of 5 to 10 cm on the skirting boards (for laying in large rooms leave the coating for 24 hours to stabilize it).
2. Stretch the coating, smoothing it with your hands in the direction of the opposite walls. Make sure that it covers the entire surface.
Preparing for laying linoleum 3. Cut the corners (straight cut) so that the cover fits snugly against the walls.
4How to put linoleum without gluing
Stacking without gluing is suitable for premises with an area of no more than 12 m2 or for rooms with low attendance
Laying linoleum without gluing 1. Unfold the roll of the coating, as indicated in the «Preparation» section.
2. Cut the cover along the skirting boards with a knife-cutter
How to put linoleum 3. Fix thresholds in doorways
Bonding with double-sided scotch tape
How to lay linoleum with double-sided scotch 1. Before laying linoleum, glue the double-sided scotch on the area of the entire room and along its perimeter, leaving a protective paper on the upper surface of the scotch.
2. Unfold the roll of the coating, as indicated in the «Preparation» section.
Laying of linoleum on the floor 3. Fold one half of the cover and fold it to the other half, remove the protective paper from the double-sided adhesive tape on that part of the floor where there is no covering, and again spread the coating, stretching it towards the walls and smoothing with your hands.
4. Do the same operation with the other half of the cover.
Laying linoleum with your own hands 5. Cut the coating along the skirting boards with a knife-cutter
How to properly lay the linoleum 5. Fix the thresholds in the doorways.
Adhesive coating
Recommended for rooms larger than 20 m2 or for rooms with significant attendance: significantly increases the service life of the coating.
How to cover linoleum 1. Unfold the roll of the coating, as indicated in the «Preparation» section.
Linoleum laying technology 2. Fold one half of the cover and fold it to the other half, glue that part of the floor where there is no covering (roller in case of using glue for fast gluing and a notched trowel in case of using professional glue).
How to lay linoleum 3. Wait for 20 minutes, then again unfold the folded part of the cover, stretching it towards the walls, smoothing with your hands.
Do the same operation with the other half of the cover.
4. Cut the cover along the skirting boards with a knife-cutter.
How to properly put linoleum 5. Secure the thresholds in the doorways and wait 24 hours before placing heavy furniture in the room.
5 More tips
In order to achieve an unseen joint in case of need to join the strips:
Joints when laying linoleum 1. Place two strips in such a way that they overlap each other by 10 cm (if the coating is patterned, be sure to combine it).
2. Fold the first strip by 2/3 of its width, apply glue and re-extend the strip.
The organization of joints when laying linoleum 3. Repeat the same operation with the second strip and smooth both glued strips, smoothing them towards the skirting boards.
4. Using a ruler, cut two layers of the coating with the breadboard knife, remove the trims and fold up both strips. Glue the remaining parts and smooth them, smoothing towards the center.
| Способ укладки | Рекомендуемое назначение | Преимущества | Недостатки |
| Укладка без приклеивания | Подходит для помещений площадью не более 12 м2 или для помещений с низкой посещаемостью |
|
|
| Приклеивание на двусторонний скотч | Подходит для помещений со средней посещаемостью |
|
|
| Приклеивание клеем, предназначенным для быстрого приклеивания и снятия покрытия | Обязательно для помещений площадью больше 20 м2 или для помещений со значительной посещаемостью |
| |
| Приклеивание специальным профессиональным клеем | Обязательно для помещений площадью больше 20 м2 или для помещений со значительной посещаемостью |
|
|
 1. Замерьте максимальную длину и ширину помещения.2. Добавьте к полученным замерам по 10 см. 3. Учитывайте выступы (пространство под стенными шкафами, окном, дверью). 4. При совмещении узора необходимо рассчитывать количество материала таким образом, чтобы оставался запас на один раппорт узора в каждом направлении. |
 1. Разверните рулон и расстелите покрытие в комнате, оставив запас от 5 до 10 см на плинтусах (для укладки в больших помещениях оставьте покрытие на 24 часа для его стабилизации).2. Растяните покрытие, разглаживая его руками в направлении противоположных стен. Удостоверьтесь в том, что оно закрывает всю поверхность. |
 3. Разрежьте углы (прямой разрез) таким образом, чтобы покрытие плотно прилегало к стенам. |
| Укладка без приклеивания подходит для помещений площадью не более 12 м2 или для помещений с низкой посещаемостью |
 1. Разверните рулон покрытия, как было указано в разделе «подготовка».2. Отрежьте покрытие вдоль плинтусов с помощью ножа-резака |
 3. Закрепите пороги в дверных проемах |
| Приклеивание двусторонним скотчем |
 1. Пред тем как настелить линолеум, наклейте двусторонний скотч по площади всей комнаты и по ее периметру, оставив защитную бумагу на верхней поверхности скотча.2. Разверните рулон покрытия, как было указано в разделе «подготовка». |
 3. Отогните одну половину покрытия и сложите ее на другую половину, удалите защитную бумагу с двустороннего скотча на той части пола, где нет покрытия, и вновь расстелите покрытие, растягивая его по направлению к стенам и разглаживая руками.4. Проделайте ту же операцию с другой половиной покрытия. |
 5. Отрежьте покрытие вдоль плинтусов с помощью ножа-резака |
 5. Закрепите пороги в дверных проемах. |
| Приклеивание покрытия Рекомендовано для помещений площадью больше 20 м2 или для помещений со значительной посещаемостью: значительно увеличивает срок службы покрытия. |
 1. Разверните рулон покрытия, как было указано в разделе «подготовка». |
 2. Отогните одну половину покрытия и сложите ее на другую половину, проклейте ту часть пола, где нет покрытия (валиком в случае использования клея для быстрого приклеивания и зубчатым шпателем в случае использования профессионального клея). |
 3. Подождите 20 минут, затем вновь разверните сложенную часть покрытия, растягивая его по направлению к стенам, разглаживая руками. Проделайте ту же операцию с другой половиной покрытия.4. Отрежьте покрытие вдоль плинтусов с помощью ножа-резака. |
 5. Закрепите пороги в дверных проемах и подождите 24 часа, прежде чем расставлять в комнате тяжелую мебель. |
 1. Положите две полосы таким образом, чтобы они перекрывали друг друга на 10 см (если на покрытие нанесен узор, следите за тем, чтобы совместить его). 2. Сложите первую полосу на 2/3 ее ширины, нанесите клей и снова разверните полосу. |
 3. Повторите ту же операцию со второй полосой и разровняйте обе приклеенные полосы, разглаживая их по направлению к плинтусам.4. Используя линейку, разрежьте макетным ножом два слоя покрытия, удалите обрезки и сложите обе полосы. Приклейте оставшиеся части и разровняйте их, разглаживая по направлению к центру. |
Way of packing
Recommended use Advantages Disadvantages
Stacking without gluing Suitable for rooms with an area of no more than 12 m2 or for premises with low attendance
Fast
Stowage
Risk of rapid wear
Significant risk of formation of «waves»
Bonding on double-sided scotch tape
Suitable for rooms with average attendance
Fast
Stowage
Risk of formation of «waves»
Leaves marks after peeling off the coating
Bonding with glue intended for fast gluing and removal of coating. Mandatory for rooms larger than 20 m2 or for rooms with significant attendance
Rapid roll packing
Easy peeling off
Significantly increases the service life of the coating
Adhesive bonding with special professional adhesive. Mandatory for rooms larger than 20 m2 or for premises with significant attendance
High-strength bonding for long-term use
Significantly increases the service life of the coating
Labor-intensive peeling off
2 Counting the required amount of material
Calculating the amount of linoleum for laying 1. Measure the maximum length and width of the room.
2. Add 10 cm to the measurements.
3. Take into account the ledges (the space under the wall cabinets, the window, the door).
4. When combining the pattern, it is necessary to calculate the amount of material in such a way that there remains a margin for one repeat of the pattern in each direction.
3 Preparation
The floor must be flat, clean, dry and free from dust: if there are unevenness or cracks on the floor, it is necessary to level it with a leveling mixture beforehand.
Preparation of linoleum for laying 1. Unfold the roll and spread the coating in the room, leaving a margin of 5 to 10 cm on the skirting boards (for laying in large rooms leave the coating for 24 hours to stabilize it).
2. Stretch the coating, smoothing it with your hands in the direction of the opposite walls. Make sure that it covers the entire surface.
Preparing for laying linoleum 3. Cut the corners (straight cut) so that the cover fits snugly against the walls.
4How to put linoleum without gluing
Stacking without gluing is suitable for premises with an area of no more than 12 m2 or for rooms with low attendance
Laying linoleum without gluing 1. Unfold the roll of the coating, as indicated in the «Preparation» section.
2. Cut the cover along the skirting boards with a knife-cutter
How to put linoleum 3. Fix thresholds in doorways
Bonding with double-sided scotch tape
How to lay linoleum with double-sided scotch 1. Before laying linoleum, glue the double-sided scotch on the area of the entire room and along its perimeter, leaving a protective paper on the upper surface of the scotch.
2. Unfold the roll of the coating, as indicated in the «Preparation» section.
Laying of linoleum on the floor 3. Fold one half of the cover and fold it to the other half, remove the protective paper from the double-sided adhesive tape on that part of the floor where there is no covering, and again spread the coating, stretching it towards the walls and smoothing with your hands.
4. Do the same operation with the other half of the cover.
Laying linoleum with your own hands 5. Cut the coating along the skirting boards with a knife-cutter
How to properly lay the linoleum 5. Fix the thresholds in the doorways.
Adhesive coating
Recommended for rooms larger than 20 m2 or for rooms with significant attendance: significantly increases the service life of the coating.
How to cover linoleum 1. Unfold the roll of the coating, as indicated in the «Preparation» section.
Linoleum laying technology 2. Fold one half of the cover and fold it to the other half, glue that part of the floor where there is no covering (roller in case of using glue for fast gluing and a notched trowel in case of using professional glue).
How to lay linoleum 3. Wait for 20 minutes, then again unfold the folded part of the cover, stretching it towards the walls, smoothing with your hands.
Do the same operation with the other half of the cover.
4. Cut the cover along the skirting boards with a knife-cutter.
How to properly put linoleum 5. Secure the thresholds in the doorways and wait 24 hours before placing heavy furniture in the room.
5 More tips
In order to achieve an unseen joint in case of need to join the strips:
Joints when laying linoleum 1. Place two strips in such a way that they overlap each other by 10 cm (if the coating is patterned, be sure to combine it).
2. Fold the first strip by 2/3 of its width, apply glue and re-extend the strip.
The organization of joints when laying linoleum 3. Repeat the same operation with the second strip and smooth both glued strips, smoothing them towards the skirting boards.
4. Using a ruler, cut two layers of the coating with the breadboard knife, remove the trims and fold up both strips. Glue the remaining parts and smooth them, smoothing towards the center.