Как сделать экран под ванной
Чтобы понять, как сделать экран под ванну, воспользуйтесь следующими советами:
Каркас
Экран под ванной устанавливается на каркас из деревянных брусков 40 х 40 мм, расположенных по краям ванной и прикрепленных к стенам.
А) ПОДГОТОВКА
На рисунке показана подготовка к работе в случае, когда ванна расположена в углу комнаты, но этот порядок работы подходит для любой планировки.
6. Напилите деревянные бруски 40 х 40 мм, имеющие следующие размеры:
Б) КРЕПЛЕНИЕ
Экран
To understand how to make a screen for a bath, use the following tips:
1Carcas
The screen under the bathroom is installed on a frame made of wooden blocks 40 x 40 mm, located along the edges of the bathroom and attached to the walls.
A) PREPARATION
The figure shows the preparation for work in the case where the bath is located in the corner of the room, but this work order is suitable for any layout.
How to make a screen under a bath
1. Using a plumbline, draw a vertical line on the wall that touches the corner of the bathroom.
2. Place the second line parallel to the first line and 2.5 cm away from it. Erase the first line.
Markup for the screen below the bathroom
3. Attach the plumb line to the corner of the bathroom and mark the appropriate point on the floor.
Measurements for the screen under the bathroom
4. Draw a square with an angle at this point and with sides 2.5 cm long so that the square is located under the sides of the bath. A similar indent is necessary for a reserve for the thickness of the panel of the screen and the skin (tiles).
Installing the screen under the bathroom
5. From the corner of the square diagonally opposite the point marked by the plumb line, draw the lines to the bottom of the lines drawn on the walls.
6. Draw 40 x 40 mm wooden blocks having the following dimensions:
For vertical parts of the frame:
4 bars, the length of which is equal to the distance between the bottom surface of the side of the bathroom and the floor.
For horizontal parts of the frame:
2 bars, the length of which is equal to the length of the line drawn along the floor along the short side of the bath with a deduction of 80 mm (double thickness
Bar).
2 bars, the length of which is equal to the length of the line drawn along the floor along the long side of the bathtub with the deduction of 120 mm (triple thickness of the bar).
B) MOUNTING
For the side frame (short side)
Mounting the end frame for the screen under the bath
1. Use the corners to assemble the frame of the four bars.
2. Drill holes in the frame, which will be attached to the wall at 2 points.
Mounting the end frame to the wall
3. Drill the wall at the appropriate points.
4. Secure the frame to the wall. Use wood screws and dowels that match the materials (monolithic wall, hollow wall, brick, wall block).
Helpful advice
To make the structure more durable, screw the bottom bar to the floor.
For the side frame (long side)
Fastening the frame for the long side of the bathtub
Mounting is the same as for a small frame. Two frames are connected with each other by screws.
2 Screen
MATERIALS
Materials for the screen under the bath Two panels of chipboard with a thickness of 16 mm or moisture-proof gypsum board — a small panel, the size of which corresponds to the size of a small frame.
The large panel has the same height as the front side frame (long side).
Its length is equal to the length of the frame
+ Thickness of the bar (40 mm)
+ Thickness of the small panel (16 mm).
It is necessary to have hinges and a metal clamp
A) PREPARATION
Substrate preparation
Using an electric jig saw, drill a large hole in the large panel for the inspection window from the side of the pipes and drainage. Calculate the exact location of the hole, depending on the desired lining of the screen.
A viewing window in the bathroom screen
B) MOUNTING
Fix the viewing window with the help of loops at the end of the hole and attach the metal clip on the opposite end to close it.
Fastening of panels
Screw the small panel to the side frame.
Place the large panel on the place assigned to it and convince in observance of right angles and in stability of a design. Screw the panel to the frame.
Complete the veneer of the screen using the facing materials of your choice. You will find our recommendations in the leaflets «Leroy Merlin», dedicated to different types of cladding.
Helpful advice
Before fixing the screen under the bath with your own hands, make the necessary connections of the pipes and the drain under the bathroom.
Каркас
Экран под ванной устанавливается на каркас из деревянных брусков 40 х 40 мм, расположенных по краям ванной и прикрепленных к стенам.
А) ПОДГОТОВКА
На рисунке показана подготовка к работе в случае, когда ванна расположена в углу комнаты, но этот порядок работы подходит для любой планировки.
 1. С помощью отвеса прочертите на стене вертикальную линию, касающуюся угла ванной. |
 2. Прочертите вторую линию, параллельную первой и отстоящую от нее на 2,5 см. Сотрите первую линию. |
 3. Приложите отвес к углу ванной и отметьте на полу соответствующую точку. |
 4. Нарисуйте квадрат с углом в этой точке и со сторонами длиной 2,5 см таким образом, чтобы квадрат был расположен под бортиками ванны. Подобный отступ необходим для запаса на толщину панели экрана и обшивки (плитки). |
 5. От угла квадрата, диагонально противоположного точке, отмеченной по отвесу, проведите линии до основания линий, нарисованных на стенах. |
Для вертикальных частей каркаса:
| Для горизонтальных частей каркаса:
|
- Для боковой рамы (короткая сторона)
 1. С помощью уголков соберите раму из четырех брусков.2. Просверлите отверстия в раме, которая будет крепиться к стене в 2 точках. |
 3. Просверлите стену в соответствующих точках.4. Закрепите раму на стене. Используйте шурупы и дюбели, соответствующие материалам (монолитная стена, полая стена, кирпич, стеновой блок). |
| Полезный совет Для придания большей прочности конструкции привинтите нижний брусок к полу. |
- Для боковой рамы (длинная сторона)
 Крепление производится так же, как и для маленькой рамы. Две рамы соединены друг с другом шурупами. |
 МАТЕРИАЛЫДве панели ДСП толщиной 16 мм или влагостойкий гипcокартон — маленькая панель, размер которой соответствует размеру маленькой рамы.
|
- Необходимо иметь петли и металлический зажим
 С помощью электрического лобзика выпилите в большой панели отверстие для смотрового окна со стороны расположения труб и слива. Рассчитайте точное расположение отверстия в зависимости от желаемой облицовки экрана. |
 Б) КРЕПЛЕНИЕЗакрепите смотровое окно с помощью петель на торце отверстия и прикрепите металлический зажим на противоположном торце для того, чтобы его закрывать. |
 Привинтите маленькую панель к боковой раме.Поместите большую панель на предназначенное ей место и убедите- сь в соблюдении прямых углов и в устойчивости конструкции. Привинтите панель к раме.Завершите облицовку экрана, используя облицовочные материалы по своему выбору. Вы найдете наши рекомендации в буклетах «Леруа Мерлен», посвященных различным видам облицовки. |
| Полезный совет Прежде чем крепить экран под ванну своими руками, выполните необходимые соединения труб и слива под ванной. |
1Carcas
The screen under the bathroom is installed on a frame made of wooden blocks 40 x 40 mm, located along the edges of the bathroom and attached to the walls.
A) PREPARATION
The figure shows the preparation for work in the case where the bath is located in the corner of the room, but this work order is suitable for any layout.
How to make a screen under a bath
1. Using a plumbline, draw a vertical line on the wall that touches the corner of the bathroom.
2. Place the second line parallel to the first line and 2.5 cm away from it. Erase the first line.
Markup for the screen below the bathroom
3. Attach the plumb line to the corner of the bathroom and mark the appropriate point on the floor.
Measurements for the screen under the bathroom
4. Draw a square with an angle at this point and with sides 2.5 cm long so that the square is located under the sides of the bath. A similar indent is necessary for a reserve for the thickness of the panel of the screen and the skin (tiles).
Installing the screen under the bathroom
5. From the corner of the square diagonally opposite the point marked by the plumb line, draw the lines to the bottom of the lines drawn on the walls.
6. Draw 40 x 40 mm wooden blocks having the following dimensions:
For vertical parts of the frame:
4 bars, the length of which is equal to the distance between the bottom surface of the side of the bathroom and the floor.
For horizontal parts of the frame:
2 bars, the length of which is equal to the length of the line drawn along the floor along the short side of the bath with a deduction of 80 mm (double thickness
Bar).
2 bars, the length of which is equal to the length of the line drawn along the floor along the long side of the bathtub with the deduction of 120 mm (triple thickness of the bar).
B) MOUNTING
For the side frame (short side)
Mounting the end frame for the screen under the bath
1. Use the corners to assemble the frame of the four bars.
2. Drill holes in the frame, which will be attached to the wall at 2 points.
Mounting the end frame to the wall
3. Drill the wall at the appropriate points.
4. Secure the frame to the wall. Use wood screws and dowels that match the materials (monolithic wall, hollow wall, brick, wall block).
Helpful advice
To make the structure more durable, screw the bottom bar to the floor.
For the side frame (long side)
Fastening the frame for the long side of the bathtub
Mounting is the same as for a small frame. Two frames are connected with each other by screws.
2 Screen
MATERIALS
Materials for the screen under the bath Two panels of chipboard with a thickness of 16 mm or moisture-proof gypsum board — a small panel, the size of which corresponds to the size of a small frame.
The large panel has the same height as the front side frame (long side).
Its length is equal to the length of the frame
+ Thickness of the bar (40 mm)
+ Thickness of the small panel (16 mm).
It is necessary to have hinges and a metal clamp
A) PREPARATION
Substrate preparation
Using an electric jig saw, drill a large hole in the large panel for the inspection window from the side of the pipes and drainage. Calculate the exact location of the hole, depending on the desired lining of the screen.
A viewing window in the bathroom screen
B) MOUNTING
Fix the viewing window with the help of loops at the end of the hole and attach the metal clip on the opposite end to close it.
Fastening of panels
Screw the small panel to the side frame.
Place the large panel on the place assigned to it and convince in observance of right angles and in stability of a design. Screw the panel to the frame.
Complete the veneer of the screen using the facing materials of your choice. You will find our recommendations in the leaflets «Leroy Merlin», dedicated to different types of cladding.
Helpful advice
Before fixing the screen under the bath with your own hands, make the necessary connections of the pipes and the drain under the bathroom.